Guide · Updated for 2026
How to Bolt Down a Safe: Concrete Floors, Wood Floors, Walls and Rentals
The makers’ own steps for anchoring a safe to concrete, a wood floor or the studs, and what to do when you can’t drill.
By the SafesGeek Review Team. We earn a commission if you buy through our links, at no cost to you.
The short answer
How to bolt down a safe: use the holes the maker put in it, never new ones. On concrete, drill through those holes into the slab and set wedge or sleeve anchors (most gun-safe makers use 3/8-inch). On a wood floor, drive lag screws into the floor joists, not just the plywood. A wall safe screws into the studs; drywall alone won’t hold it. Renting? Cable it to something fixed or screw it into furniture you own. Bolting won’t stop a thief with tools and time, but it stops the easiest theft of all: carrying the safe off and opening it somewhere quiet.
The steps below come from safe makers’ manuals and anchor makers’ instructions. Where makers disagree, we say so: your own safe’s manual wins.
Should you bolt your safe to the floor?
Yes. Liberty’s warranty says safes should be bolted to the floor for the best security, and some makers go further: Cannon’s manual says a safe that isn’t fastened down voids the warranty, and Rhino says you must anchor the safe for its break-in warranty to count.
The reason is simple. A thief who can’t open a safe in a few minutes can still carry it out and work on it at leisure. It’s the most repeated point in every owner discussion we read: an unbolted small safe leaves the house whole, on a dolly or in someone’s arms. Owners and pros add a fair point the other way: even a loose safe beats none, because most burglars can’t open one and many get dumped unopened. But bolting takes the grab-and-go option away.
What bolting won’t do is make a safe burglar-proof. It buys time. UL’s test for a residential security container, the lowest burglary rating, is 5 minutes against one person with hand tools, and a safe made to be bolted down is tested bolted down. If you want a rating against tools, see our safes with a burglary rating. If you’re still shopping, our safes that ship with floor bolts all come with the hardware in the box.
Before you drill: move it in, check the floor, pick the spot
Do these things before the drill comes out, because a bolted safe is hard to move again.
- Move it in empty. Take out the shelves and the contents, and use an appliance dolly with straps and enough people. For a full-size gun safe or any stairs, owners mostly say safe movers are worth hiring. Our safe dolly picks cover the hand trucks and stair climbers built for the job.
- Check the floor can take it. US homes are built for a live load of 40 pounds per square foot in living areas and 30 in bedrooms (the International Residential Code). A concrete slab carries a heavy safe easily. On a wood floor upstairs, Liberty says to set the safe across several joists and against a load-bearing wall, and to ask a professional for anything over 1,000 pounds. The most upvoted answer we found on this topic says the same about apartments: check the floor before a heavy safe goes upstairs.
- Pick the spot. Cannon’s manual says the safe should sit flat against a wall, and owners like a corner: a thief can’t tip a safe onto its back to pry the door if there’s no room to swing a bar. Leave room for the door to open all the way. A closet works well, and closet walls have studs.
- Check what’s under it. Some slabs are post-tensioned: steel cables under high tension run through the concrete. Liberty says those slabs are stamped with a warning not to drill, cut or core, and the Post-Tensioning Institute recommends scanning the slab before any opening. Owners also warn about water pipes and heating lines in slabs. If in doubt, ask the builder or a scanning service first.
On carpet: Browning’s manual warns that a safe standing on plush carpet can tip when you open the door. Bolting it down is what keeps it steady.
How to bolt down a safe on a concrete floor
Concrete is the best anchor you have. Here’s how to bolt down a safe on a slab, in the steps the gun-safe makers give (Cannon, Browning, Rhino, Liberty), with the details from the anchor makers’ own instructions:
- Empty the safe and take the shelves out. Lift the carpet on the safe’s floor and take the caps off the anchor holes. On some fire-lined safes the holes are filled with fire caulking: Cannon says to drill it out with a 3/8-inch bit.
- Mark the floor. Set the safe exactly where it will stay and mark the concrete through the factory holes. Then move the safe aside.
- Drill the holes. Use a hammer drill and a masonry bit. The makers we checked use 3/8-inch anchors: Cannon specifies 3/8 by 3-3/4-inch wedge anchors and Rhino 3/8 by 3-inch sleeve anchors in holes about 3.5 inches deep. The anchor maker’s rule: the bit is the same size as the anchor, and the hole goes at least 1/4 inch deeper than the anchor’s embedment.
- Clean the holes. Blow or vacuum the dust out. Dust left in the hole weakens the grip.
- Bolt it down. Put the safe back, set the anchors through the safe’s holes into the floor, and tighten them from inside to the torque on the anchor’s box (Red Head gives 25 foot-pounds for a 3/8-inch wedge anchor, and says not to use an impact wrench). Use the washers or gaskets your safe came with: on Cannon safes they’re what keeps the fire and water ratings.
Two cautions. Wedge anchors are made for solid concrete. Red Head, Hilti and Simpson rate theirs for concrete or grout-filled block, not hollow block, and Hilti lists a minimum slab thickness of 3-1/4 to 5 inches for a 3/8-inch anchor. And makers differ on the hole size: Cannon says to drill 7/16 inch for its anchor, while the anchor makers match the bit to the anchor. Follow your safe’s manual and the sheet in the anchor box.
Owners who’ve done it mostly use four anchors, one in each corner, set from inside so no bolt heads show outside the safe. Want a safe that’s set into the slab itself instead? See our floor safes set into concrete.
Bolting a safe to a wood floor: find the joists
Here’s the catch with wood: the plywood subfloor is thin, and screws that only bite into it can be levered out. The makers all say the same thing: lag screws with washers, into the floor joists.
- Find the joists. They’re usually 16 or 24 inches apart. Check from the basement or crawl space if you can, or with a stud finder.
- Drill pilot holes to your manual’s size. The makers don’t agree: Liberty says 1/4 inch, SentrySafe 9/32 inch and 2-1/2 inches deep, Browning and Cannon 5/16 inch. Simpson Strong-Tie, which makes the screws, says lag screws over 3/8 inch need a pre-drilled hole.
- Put a washer under each head and tighten until snug. Don’t strip the wood.
Make sure each screw reaches a joist: one that only holds the plywood is the weak point a pry bar finds. Wood is still the weaker anchor, so on a gun safe with wall holes, a wall anchor too is worth it (next section). Most of our bolt-down safes ship with expansion bolts made for concrete; on wood, plan on buying lag screws long enough to reach the joist.
Can you bolt a gun safe to the floor and the wall?
Sometimes, and the makers disagree. Browning’s European manual recommends anchoring to the floor and the wall. Liberty advises against wall anchoring for large safes, because drilling the back can go through the fireboard and weaken the fire rating, and SentrySafe says its fire safes shouldn’t be bolted to a wall at all. So: bolt the floor first, and the wall only through holes the maker provides. Owners who use both say it stops the safe being tipped over and pried. The safes on our gun safes weigh 250 to 800 pounds, and every one of them should still be bolted down.
Gun cabinets are a different story. They’re light and top-heavy, and a full door swinging open can tip one over. Stack-On’s instructions warn that a child or an adult can tip a cabinet and be killed. They screw it to the wall studs: 1/4 by 1-1/2-inch lag screws through the top holes, into 3/16-inch pilot holes, with the holes lined up on studs 16 inches apart (or two into the wall and two into the floor). Our gun cabinets guide covers the cabinets themselves.
How would you bolt a safe to the wall of your home?
An in-wall safe sits in the space between two studs and screws into both. Here’s how Hornady’s in-wall safe manual does it:
- Check the space. Studs 16 inches apart, center to center, leave about 14.5 inches between them. Barska notes most studs are 16 or 24 inches apart.
- Check what’s in the wall. Walls hide pipes, wires and ducts, and both Hornady and Barska say to check before you cut. A wall built with 2×4s is only about 3.5 inches deep inside, which is why wall safes are 3 to 4 inches deep.
- Cut, set and screw. Cut the opening to the size the maker gives, set the safe in, pre-drill each stud (Hornady: a 1/4-inch bit) and drive the lag screws through the safe’s side holes into the studs. Don’t over-tighten.
Studs 24 inches apart? Some wall safes ship with a spacer kit that gives them something solid to screw into. Drywall anchors or hollow-wall fixings alone won’t hold a safe: the drywall comes out with it. In a concrete or block wall, use masonry anchors into solid concrete, as on a slab; owners say that’s far harder to pull out.
Be realistic about what a wall safe is. A box screwed to wooden studs can be pried out with the wall around it, so its real defense is not being found. Our wall safes that fit between studs show which ones fit 16- and 24-inch spacing.
Renting? How to anchor a safe without drilling
Ask your landlord first, and get the answer in writing: some allow a few small screw holes, and a safe bolted to the floor beats anything else here. If the answer is no:
- Cable it. Many small safes come with a steel security cable. Vaultek’s instructions: loop it around something fixed, like a bed frame or a pipe, and lock the end inside the safe.
- Screw it into your own furniture, like a dresser or a closet shelf you own.
- Keep it out of sight. A cable can be cut, so a thief who never finds the safe never gets to try.
A very heavy safe is the other option, but only on a floor that can take it (see the floor loads above). Our no-drill safes for renters all come with a cable.
Does bolting down void the warranty or the fire rating?
Not if you follow the manual. Here’s what the makers say:
- Liberty: anchoring doesn’t void the warranty, but drilling new holes the maker didn’t provide could.
- Cannon and Rhino: their warranties need the safe anchored.
- SentrySafe: bolting a fire safe down as the manual says doesn’t affect its fire protection, but most of its safes are no longer water resistant once bolted (its FPW082 keeps its water rating with SentrySafe’s own bolt-down kit). Some SentrySafe fire safes are drilled from outside, through marks on the feet, and never from inside.
The rule underneath all of them: no new holes through a fire safe’s walls, floor or back, and seal any hole the way the manual says (Browning: high-temperature silicone).
- Read your safe’s manual: where the holes are, what size anchors, drill from inside or outside.
- Check the floor: concrete or joists, a post-tension stamp, pipes or wires, and the weight it can take.
- Place the safe: back to a wall, ideally a corner, with room for the door to swing open.
- Concrete: hammer drill, bit the same size as the anchor, clean holes, wedge or sleeve anchors, tightened to the box.
- Wood: find the joists; lag screws with washers, pilot holes to the manual’s size.
- Wall safe: a stud bay with no wires or pipes, screws into both studs.
- Fire safe: no new holes, and no wall bolts unless the maker allows them.
- Test the lock and the door before you fill it.
Safes that come ready to anchor
Bolt-down hardware in the box, 125 pounds, UL-rated for an hour at 1700°F.
Screws into the studs, with a spacer kit for studs 24 inches apart and a key lock with no batteries.
A steel cable and furniture mounting in the box, no drilling.
Related guides
Quick answers
What size bolts do I need to anchor a safe?
The gun-safe makers we checked use 3/8-inch concrete anchors (Cannon and Rhino). Use the kit from your safe’s maker or the size in your manual.
Can I use drywall anchors to mount a safe?
No. Drywall anchors pull out with the drywall. Screw into the studs, or into concrete.
How many bolts should a safe have?
Use every factory hole. Most freestanding safes have four, one in each corner.
Can I bolt a safe in a closet?
Yes, and it’s a good spot: out of sight, and closet walls have studs. Measure the closet door and the ceiling height first.
Will a bolted-down safe stop a burglar?
It stops the thief who wants to carry it off. Someone with power tools and time can still get in, so bolting buys time, not certainty.
Sources: Liberty Safe: Limited Lifetime Warranty, “Anchoring your gun safe to the floor”, “Preventing safe tipping”, “Your gun safe and concrete floors”, “Planning your safe placement”; Cannon Safe user manuals and FAQ; Browning safe owner’s manuals (US and European ProSteel); Rhino Metals gun safe owner’s manual; SentrySafe fire safe owner’s manual and Master Lock support (bolt-down FAQ, kits P50211 and P72294); Stack-On gun cabinet instructions (GCM-1918-DX, GC-908-5); Hornady SnapSafe in-wall safe manual; Barska wall safe manual; Vaultek VT/VTi support; ITW Red Head Trubolt wedge anchor instructions; Hilti KB-TZ2 technical guide; Simpson Strong-Tie; UL 1037 (Residential Security Containers); ICC International Residential Code, Table R301.5; Post-Tensioning Institute. Owner reports: topic level only. Checked November 2026.
